BC Transistor Datasheet pdf, BC Equivalent. Parameters and Characteristics. C NTE Equvilent NTE PNP audio amplifier transistor. NTE Silicon PNP Transistor Audio Amplifier. Switch (Compl to NTEAP). NTE Data Sheet. PNP Epitaxial Silicon Transistor. Features. • Switching and Amplifier. • High- Voltage: BC, VCEO = V. • Low-Noise: BC, BC

Author: Vudok Gagami
Country: Philippines
Language: English (Spanish)
Genre: Business
Published (Last): 26 March 2012
Pages: 223
PDF File Size: 16.92 Mb
ePub File Size: 6.48 Mb
ISBN: 752-5-33181-825-3
Downloads: 24026
Price: Free* [*Free Regsitration Required]
Uploader: Misar

Submitted by admin on 30 August Yransistor uses as an Amplifier the DC current gain of the Transistor can be calculated by using the below formulae. Complete Technical Details can be found at the datasheet give at the end of this page.

Of the above types common emitter type is the popular and mostly used configuration. As discussed a transistor will act as an Open switch during Forward Bias and as a Closed switch during Reverse Bias, this biasing can be achieved by supplying the required amount of current to the base pin.

If you are designing a PCD or Perf board with this component then the following picture from the BC Datasheet will be useful to know its package type and dimensions. Amplifier modules like Audio amplifiers, signal Amplifier etc.

TRANSISTOR C B datasheet & applicatoin notes – Datasheet Archive

Submitted by admin on 26 October The value of transisror resistor R B can be calculated using below formulae. BC has a gain value of tothis value determines the amplification capacity of the transistor.

As mentioned the biasing current should maximum of 5mA. Controls the biasing of transistor.

BC557 Philips Transistor RARE To-92 Last Ones

If you are designing a PCD or Perf board with this component then the following picture from the Datasheet will be useful to know its package type and dimensions. As discussed teansistor transistor will act as an Open switch during Forward Bias and as a Closed switch during Reverse Bias, this biasing can be achieved by supplying the required amount of current to the base pin.

  CLAN MEKHET PDF

To bias a transistor we have to supply current to base pin, this current I B should be limited to 5mA. It can amplify power, voltage and current at different configurations.

The maximum amount of current that could flow through the Collector pin is mA, transistoe we cannot connect loads that consume more than mA using this transistor. TL — Programmable Reference Voltage. Anything more than 5mA will kill the Transistor; hence a resistor is always added in series with base pin. It can amplify power, voltage and current at different configurations. As mentioned the biasing current should maximum of 5mA.

Some of the configurations used in amplifier circuits are Common emitter amplifier Common collector amplifier Common base amplifier Of the above types common emitter type is the popular and mostly used configuration.

When uses as an Amplifier the DC current gain of the Transistor can be calculated by using the below formulae. When base current is removed the transistor becomes fully off, this stage is trabsistor as the Cut-off Region and the Base Emitter voltage could be around mV.

When this transistor is fully biased then it can allow a maximum of mA to flow across the collector and emitter. When a transistor is used as a switch it is operated in the Saturation and Cut-Off Region as explained above. To bias a transistor we have to supply current to base pin, this current I B should be limited to 5mA.

  BORTEZOMIB MSDS PDF

Cc557 base current is removed the transistor becomes fully off, this stage is called as the Cut-off Region and the Base Emitter voltage could be around mV. BC is a NPN transistor hence the collector and emitter will be left open Reverse biased when the base pin is held at ground and will be closed Forward biased when a signal is provided to base pin.

5c57 the above types common emitter type is the popular and mostly used configuration. The maximum amount of current that could flow through the Collector pin is mA, hence we cannot connect loads that consume more than mA using this transistor.

Anything more than 5mA will kill the Transistor; hence a resistor is always added in series with base pin. The value of I B should not exceed mA. Current Drains out through emitter. BC Transistor as switch When a transistor is used as a switch it is operated in the Saturation and Cut-Off Region as explained above. When a transistor is used as a switch it is operated in the Saturation and Cut-Off Region as explained above. The value of I B should not exceed mA.

A Transistors acts as an Amplifier when operating in Active Region. TL — Programmable Reference Voltage.

C557, PNP Silicon, Amplifier Transistor, TO-92

A Transistors acts as an Amplifier when operating in Active Region. BC is a PNP transistor hence the collector and emitter will be closed Forward biased when the base pin is held at ground tranistor will be opened Reverse biased when a signal is provided to base pin.

Current flows in through collector.

Last modified: September 4, 2020